Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NORYL GTX™ Resin GTX909 - Americas - (PPE+PA*) - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for NORYL GTX™ Resin GTX909 - Americas:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Noryl GTX datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Mechanical properties - Thermal properties - Electrical properties - Other properties - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
Product Texts
NORYL GTX™ 909 resin is a non-reinforced alloy of Polyphenylene Ether (PPE) + Polyamide (PA). This injection moldable grade exhibits high impact performance, high heat resistance, and excellent chemical resistance. NORYL GTX909 resin may be an excellent candidate for various exterior automotive applications such as door handles and wheel covers.
Mechanical propertiesValueUnitTest Standard
ASTM Data
Tensile Strength at Yield 66 MPa ASTM D 638
Tensile Strength at Break 59 MPa ASTM D 638
Elongation at Yield 9 % ASTM D 638
Elongation at Break 50 % ASTM D 638
Izod Impact notched, 1/8 in 176 J/m ASTM D 256
Izod Impact notched, Low-Temperature 106 J/m ASTM D 256
Temperature -30 °C -
Thermal propertiesValueUnitTest Standard
ASTM Data
Vicat Temperature 245 °C ASTM D 1525
Electrical propertiesValueUnitTest Standard
ASTM Data
Dielectric Strength, Short Time 25.5 kV/mm ASTM D 149
Dissipation Factor, 60 Hz 0.039 - ASTM D 150
Dissipation Factor, 1 MHz 0.019 - ASTM D 150
Dielectric Constant, 60 Hz 3.27 - ASTM D 150
Dielectric Constant, 1 MHz 2.76 - ASTM D 150
Surface Resistivity >1E15 Ohm ASTM D 257
Volume Resistivity >1E15 Ohm*cm ASTM D 257
Other propertiesValueUnitTest Standard
Density 1130 kg/m³ ASTM D 792
Processing Recommendation Injection MoldingValueUnitTest Standard
Pre-drying - Temperature 95 - 105 °C -
Pre-drying - Time 3 - 4 h -
Processing humidity ≤0.07 % -
Melt temperature 270 - 295 °C -
Mold temperature 65 - 95 °C -
Zone 1 255 - 295 °C -
Zone 2 260 - 295 °C -
Zone 3 265 - 295 °C -
Screw speed 20 - 100 rpm -
Back pressure 0.3 - 1.4 MPa -
Characteristics
Processing
Injection Molding
Applications
Automotive
Regional Availability
North America
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.